una preguntica, el vdrop es standard en cada modelo de board, por ejemplo todas las 965p-ds3 rev 2.0 tienen el mismo vdrop?
Gracias
Gracias
una preguntica, el vdrop es standard en cada modelo de board, por ejemplo todas las 965p-ds3 rev 2.0 tienen el mismo vdrop?
Gracias
Pues por el contrario los OCker Pro les gusta esta ultilidad para ajustar sus memos a timming agresivos a grandes Frecuencias y probar su rendimiento.Yo no se si estoy subvalorando la utilidad de MemSet o que pero a mi no me gusta usar ese programa para que esté cambiando los valores automáticamente. Solo lo uso como utilidad de consulta para la frecuencia y Timmings de la memoria.
Es la suma del tRP + tRASLa pregunta es el tRC que valor es??
¿Alguno me puede decir cuáles son las relaciones restantes? ¿O el significado de los otros parámetros y su influencia?
tCL:
Large influence on stability / Medium influence on bandwidth
From CAS 5 to 4 results change ~5-10mb/s. The same change will most likely be seen when going to CAS 3. This timing is widely seen as most important (Command rate disregarded).
Recommendation: 4 for normal usage, 5 when oc"ing. Tweaked: 3.
tRCD:
Medium influence on stability / Large influence on bandwidth
tRCD going from 4 to 3 gives ~15mb/s. From 5 to 4 also yields 10-15mb/s. This timing is considered second important after CAS, but actually it"s more important on 680i/DDR2.
Recommendation: 4 for oc/normal usage. 5 if you want to push mhz. Tweaked: 3
tRP:
Medium/small influence on stability / Small influence on bandwidth
Results vary close to nothing when changing from 3 to 4 to 5. Still this timing needs to finish its cycle before a new one starts, so dont set it higher than 5.
Recommendation: 4 for oc/normal usage. 5 if you want to push mhz. Tweaked: 3
tRAS:
Small influence on stability / Small influence on bandwidth
tRAS seems to act differently on integer/float results. Integer, going from 15 to 10 changes by ~5mb/s. Float doesnt change.
tRAS is an "end-timing", so dont go to high. And not lower than what tCL+tRCD equals.
Recommendation: 12 for oc/normal usage. 15 if you want to push mhz. Tweaked: 8
tRRD:
Small influence on stability / Small influence on bandwidth
tRRD of 2 didnt change the results. Nor did a tRRD of 4. This is a delay-timing so a too low value may result in recalculation.
Recommendation: Auto for oc/normal usage. 4 if you want to push mhz. Tweaked: 2
tRC:
Medium influence on stability / Large influence on bandwidth
This timing is quite surprising. Going from 30 to 21 gave ~90mb/s. From 23 to 21 gave ~15-20mb/s.
tRC is last timing before ram burst (data transfer).
Dont set too high. And tRC should be greater than tRAS + tRP or you might get corruption.
Recommendation: 21 for normal usage. 30 if you want to push mhz. Tweaked: 15
tWR:
Small influence on stability / Small influence on bandwidth
Small change from 6 to 3. Setting timing too low will cause ram to fail switching to "read mode".
Recommendation: Auto for oc/normal usage. 6 if you want to push mhz. Tweaked: 3
tWTR:
Large influence on stability / Small influence on bandwidth
From 10 to 8 didnt change results. 6 would lock up the system. This timing gives no bonus but affects stability a lot. Use with care.
Recommendation: Auto for oc/normal usage. 10 if you want to push mhz. Tweaked: 8 (7)
tREF:
Small influence on stability / Small influence on bandwidth
Changing to 3,9us didnt show improvements in benchmark. It also didnt seem to affect stability. tREF was important with DDR1.
Recommendation: Auto for oc/normal usage. 7,8us if you want to push mhz. Tweaked: 3,9us
Command Rate:
Settings are 2T/1T. You probably already know a lot about this timing.
The 680i struggles running 1T above 800mhz. So do the ram - atleast 2,2v are needed. This timing gives a great boost to bandwidth, but is fairly hard to attain. I wont recommend any setting regarding this timing. You need to find what mhz you get with 1T, then find mhz with 2T, then compare benchmarks.
Fuente: http://www.evga.com/forums/tm.asp?m=45260
Yo no se si estoy subvalorando la utilidad de MemSet o que pero a mi no me gusta usar ese programa para que esté cambiando los valores automáticamente. Solo lo uso como utilidad de consulta para la frecuencia y Timmings de la memoria.
Esos Subtimmings no están disponibles directamente en la BIOS?
Al menos en la mia no. En la BIOS tengo 9 caracteristicas y en el memset 16, a saber:
BIOS
tCL
tRCD
tRP
tRAS
tRRD
tRFC
tWR
tWTR
tRTP
El memset se puede ver en la imagen que postie anteriormente.
http://www.laneros.com/showpost.php?p=2317174&postcount=1224
Un OCsillo al Valde:
Q6600 a 3010Mhz (430x7) con 1.1875v según BIOS, (VID 1.2375v) + Xigamtek HDT S1238
ASUS P5K-E WiFi AP bios 1013
2x2GB GSKILL PQ PC8000 5-5-5-15 2.1V a 1033MHz
OCZ 600W
volts:
NB: 1.40v
CPU PLL: 1.60v
FSB Termination Voltage: 1.30v
Memos: 2.10v
CPU: 1.1875v
Se puede mejorar en algo este OC? ó así esta bien?
Gracias y Salu2.
Ese Vcore es el Setiado en la BIOS?????? porque es bastante bajo para esa frecuencia final y claro que se puede optimizar mucho mash.
Es la suma del tRP + tRAS
Pues que significa cada uno es algo que hace mucho tiempo conoci de una recopilacion que se hizo en los foros de eVGA por un usuario.
Respecto al uso el memset, como ya lo sabemos el software lo que hace es darnos la posibilidad de manipular el controlador de memoria y este proceso personalmente digo que es parte de la optimizacion del Overclock ya fase final donde de cierta manera se tiene un 80% COMPRENDIDO la estabilidad de todas las variables existentes en el proceso.